Customer reviews about Harley Benton Parts Copper Shielding Tape

A

You get a Small amount - check measurements before buying

Andrew822 12.12.2022

You get a very small amount it looks like the picture you get a decent big roll but forget it its misleading. There is not enough to do a strat maybe just enough for a tele or just when a small amount is required like on a les paul type. The tape is of good quality though but pay attention to the measurements before you buy.

24

1

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

S

A bit stingy on the quantity!

Stephen662 08.06.2024

A quality thick tape that sticks very well to you guitar cavity and to itself, with conductive adhesive. I reccomend using a tool to flatten it down and eliminate creases and bubbles - do not be tempted to use your fingers! It is incredibly sharp and you will end up with lacerated finger tips - painful and not good for a guitarist!
Now my only complaint is the amount you get. There is not enough to do the cavity of a Strat... let alone the pickguard. You will need two rolls. I think Harley Benton should measure how much it takes to do the typical strat and add on another 0.5 meter for good luck. And then price accordingly. I know you can use 'garden slug tape' but it is rarely as thick as this or as sticky. So, it's a good product but too short on quantity.

1

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

Lf

Good quality but not much tape

Leonidas from XIV 27.04.2023

The quality is pretty great, the adhesive is a good balance between stickiness and ability to work with, it is easy to cut with scissors or craft knives and it stays in position very well.

The only downside is that it is quite little tape. For Telecaster body cavities + pickgruard I needed roughly 1.5 rolls, for a Stratocaster + pickguard 1.5 rolls were not enough, I'd probably need about half to 1 roll extra to cover the entirety.

1

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

M

Does the job

MacGee 26.12.2023

I don't know why I had it in my head that I had to fork out big bucks for big branded copper shielding tape.
I bought this on a whim to insulate my tele guitar which was humming like mad under fluorescent lighting.
Cheaper than the other stuff I normally buy and it did the job perfectly.
Also, I had some left over for any patch ups on other guitars.
It's cheap and it works. I can't say any more about copper tape.

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

T

Is doing perfectly his job.

Tzst72 15.02.2023

Is doing perfectly his job.
For the cost ihas is really a good product

1

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

sp

great product!

stavros pap 03.03.2023

It sticks well, also it takes the form of the guitar electronics slot very well if you help it with a plastic card or a pen for the corners. It was enough for me to shield pot and switch slot plus 2 humbucker slots on the front. If you're in doubt just order 2.

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

d

Correspond à la description

dbeguin 23.06.2023

Petit rouleau en effet mais c'est précisé dans la description du produit.
Avec un seul rouleau j'ai pu faire mon pickguard et la plaque arrière du tremolo, et il m'en reste encore. Impossible de faire les cavités avec cependant mais ce n'est pas mon objectif, mes cavités ayant été peintes à la peinture métalique. La couche de cuivre est selon moi un peu trop importante pour l'appliquer dans les cavités facilement (pas assez maléable). Mais sur du plat, c'est tout bon.

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

J

great product

Julius93 06.10.2023

i shielded all of my guitars with this tape, and its still a lot tape left for other future shieldings. Guitars are noiseless now, i had some trouble with hum coming from the pickguard of my telecaster. Now it works perfectly fine

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

CD

Great for shielding your guitar or bass electronics

Crater Dude 06.02.2024

This is all you need to properly shield your guitar or bass electronics from electromagnetic interference. Lay it out in the control cavity and the bottom side of your pickguard, ensure good contact between the layers and you should be good to go! Nothing to complain here - good quality stuff and reasonably priced.

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

J

HB copper Shielding tape

JonMontoya 28.09.2023

Good thick copper great for pickguards. Be aware the adhesive is NOT conductive so you will need to solder every joint.That said though its thick tuff copper.
Great for shielding guitars and bass from unwanted hum and interference. One roll fully treats a guitar or bass's internal control and pickup cavities.
Overall a good Shielding at a good price as HB does.

0

Report

Do you believe this rating to be inaccurate or unacceptable for some reason? Please give us the reason for your assessment in the following text box and – if possible – your e-mail address for further questions.

Harley Benton Parts Copper Shielding Tape

208 Customer ratings

You have to be logged in to rate products.

144 Reviews

Served with love!

Harley Benton Parts Copper Shielding Tape

208 Customer ratings

You have to be logged in to rate products.

144 Reviews