Very happy with sound and use but sloppy finishing letting the brand down
For the price I paid there is some sloppy finishing on the front of the amp. The tolex was not cut clean on either of the front corners. One side is not allowing the front panel to come flush to the front of the case and on the other side the fibers protruding from inside the tolex layer were left untrimmed. A nail/tack in the corner guard was poorly installed with the hammer, thus leading to a ding in the plastic. The white piping on one side is not perfectly fitted to be flush with the gold from panel. This is disappointing sloppiness at this price-point. I recently had a DSL20H (had to return with a channel switching relay popping issue) and decided to go for this higher quality item instead. The finish on the DSL20 was better than this SC20H!!!! However these imperpection are simply imperfections and not noticeable unless you are looking for them. Disappointing though Marshall.
On to the main use - the function and sound.....
I'm very happy with how this amp sounds and having done a lot of research I'm more comfortable with a one channel amp. I can hit the front of the amp with a cheap tube-screamer clone and the amp will do an awesome 80s thrash vibe. I can on/off an EQ pedal out front with the level set to minimum to simulate rolling off the volume on the guitar to get a cleaner tone & simulate a 2 channel setup (Note: the level drop with an EQ is not the same as rolling the guitar pot down all the way - there are pedals out there that will drop the db of the signal even more to get even cleaner). I love the sound of the amp and the distortion is much more pleasant than the DSL20. I think if you are looking at both of these amps and wanting to play early metallica, megadeth etc then this is a better choice for the sound. You do need to hit it out front with the pedal though (cheap pedal for €23.90 ;-) works well here). Ok it's a lot dearer so there is that - but if you can afford either then I can say this is worth the extra cash. The sounds for classic rock are much nicer on this than on the DSL also in my opinion. Lastly on this - it's less bright. the DSL nearly took the enamel off my teeth with the treble. This amp is still on the bright side but way more manageable and pleasant. The other thing I can do, which I don't see many saying online is that I can use the EQ out front and drop the level on it to minimum while pushing up the master volume on the amp to drive the power tubes harder - without blowing my head off. This amp is very loud even on 5W mode at 1 on the master and 10 on the preamp. The proper way to do this of course is to purchase an expensive attenuator with a reactive load, but to be honest this is not a bad "poor man's way" of getting some more balls out of the amp in a much more affordable and simple way (another €23.90 gets you a perfectly good EQ pedal :-) [Note: I'm using this amp at home mostly, if you are gigging or practicing well then turn the thing up to 3 and they'll hear you in the next parish!]
The only (small) downsides/considerations on the functionality side are:
1. No reverb on-board. It's nice to have a simple way to bring in some reverb on an amp itself if you just want to plug in to the amp and play (even if it's digital and can be turned off & out of the circuit). However I will say that I don't miss the reverb much on this amp. It has a "vibrance" to it's tone. You would miss the reverb significantly on an amp with a very dry clean signal. You won't miss it as much here unless you specifically want a decent amount of reverb for your particular song/sound.
2. The FX Loop is not footswitchable. Not important for me but might be for others. The loop knocks the signal down -10dB to be pedal friendly in the loop, which is probably a good thing. Does it suck tone? I dunno, I'm pretty happy using the fx loop. you can take the fx loop out of the circuit with a switch on the back.
3. The FX loop is after the master volume. This is interesting because if you want to run into the FX Loop Return, bypass the pre-amp and just use the power amp you will need external level controls because your amps master volume is now useless. You are at full volume if you go into the return on this amp - well full volume minus 10dB!! - see above. Maybe this is not a downside as such - just thought it was interesting to know. It's how the circuit is designed - you probably have something with a level on it if intending to use it this way anyway. MT2?!
