Millenium BS-500 Set

+Stands the test of time.
I've used this Millenium BS-500 Set since 2011.
For nearly 9 years now, they've kept my Yamaha HS80M up.
With an Auralex acoustic pad in between them.

+Reliable
The weight all rests on the thick metal pin,
which is pinned at the position/height you set the shaft to be.
After all these years still reliable & no sign of wear.

+Great cable relief from connector
There's a cable hook provided to attach to the shaft for cables.
I've positioned the hook to face the front rather than the backside so the XLR cable runs in an smooth curvature from front of shaft to back at the speaker.
This way the hook takes the weight of the cable, and not the connector that hangs from the speakers.
Both cable & speaker inputs remains as good as new.
Many overlook cable weight strain on the connector, and might damage either connector or speaker input after years hanging down.

+The Triangle base
Pockets are great for tierupping/spiral rolling remaining cable.
Keeping the power cables, audio cables separate etc
It stands sturdy, with metal carpet spikes provided to screw on for minimal ground contact.

+Base can be rotated as desired to fit with desks.
And speakers all setup can still rotate.
Nice black textured coating, never dusty & easy to clean.

Everything what's expected of a speaker stand to do it does.
Just make sure you don't place overly sized speakers on it.
Or let people walk around them to much.
It can take a nudge but not a bump. Cheers V

Positive: These stands are easy to mount/ adjust and are solid. They are stable for as long as the floor is perpendicular and not askew, and the height of the pole is not set too high.

The triangle shaped foot is very handy not only for stabilization but also for fitting the stand in corners! The adjustability is very flexible and suits for one's needs. One can adjust the height of the pole and the direction of the surface holder accordingly.

There is a soft material on the corners of the surface holders which prevents the speaker from sliding and shocks.

Negative: Consider taking the measurements of contact surface area of the stand and your speakers before buying. I have the Yamaha HS8 which does not perfectly fit on the surface of the stand, the speaker comes 1 to 2 cm out of the surface.

The stand is not that stable when the speaker is bigger or heavy. The surface holder is sometimes difficult to rotate.

Extra: There is a piece of metal that I do not know exactly the utility of. This piece fits in holes of the pole, I use it as a sort of security, if ever the pole doesn't hold and collapses. By putting the piece of metal in the hole, one can prevent/block the pole from sliding to the ground if ever it fails to hold.

Do not buy this no matter what. Your precious monitors will fall to the ground the same day you put them up on this stand.

I have never before left a product review, but this got me frustrated enough to leave one.
1: An hour after I put them up one of the two stands literally cracked and fell to the ground, seems like it's a result of terrible soldering. Thank god I didn't have the monitor on it when it happened.
2: They didn't match in height, like on the same height setting one of them was approx 5 cm higher... How is that even possible, they had one job! Like how can that even happen...?? It literally wasn't possible to have the speakers on the same height level.
3: The rubber monitor pads at the top weren't symmetrical, sticking out on one side and had a bunch of plastic bits sticking out... I don't know how it even got there. In addition there was a bunch of dust and what looked like metal shavings in the packaging.
Also the packaging smelled like vomit when I opened the box.

I have learnt my lesson, I will put significantly more money into my next monitor stand purchase, and I'm getting my money back.
If you are making cheap products, please make sure that they at minimum get the main job done just as well. This is ridiculous, how is this even allowed to be sold.

They seemed sturdy, reason why I purchased them, but they are not.

VERY BAD:
- The central vertical "tube" is only held by a single screw to the middle of the base, and it is likely very weak and easy to bend/damage. It does not fit very firmly, even when screwed with a lot of force
- There is metal or paint power inside the base frame, so you have to shake the things like a mad to get out what you can. Not only that powder is likely toxic (extremely thin), but also you clearly do not want that in any studio environment (magnets from speakers, mics, guitar pickups...)
- Bad powder coating/damaged finish on the base

LESS BAD
- Feet pressed inserts at the base are moving (not properly pressed into the base)
- Plastic molded parts are low quality
- You cannot put the lower cable managers, as they simply do not fit
- Not the best welding on the base
- I wish it was possible to lower a bit more the speakers

Unless you are on a budget and do not care about a bit of frustration, go ahead. I recommend purchasing something else, especially if you plan to move them a lot. You cannot tour with that.

I was purchasing the monitor stands for my little home studio to finally get my speakers off my desk and I was pretty excited when the box arrived.

The stands are easily to assemble as an easy to use manual comes with them. As a fitting Allen Key is provided, the stands should be up and ready within a few minutes. Unpacking took longer. ;-)

But unfortunately my delivery must have been a Monday production. One of the poles was slightly different, the provided bolt was not long enough to connect the foot with the pole. Therefore I was not able to assemble the second stand straight out of the box. As I am living in Ireland I figured that returning the whole thing because of a screw would not make a lot of sense. I contacted Thomann customer support but decided to visit the next ironmonger before they even had a chance to answer. Issue resolved, stand is working fine now. But I will have to remove a few stars for quality and the overall rating.

I still recommend the BS-500 Set for small project studios as the price is more than fair for what you get.

After many hours of fiddling and faffing, one may succeed in standing these stands up in such a way as to remain silent -- without vibration or resonances -- beneath one's speakers. After that, they'll do -- that is, they'll do, for a week or a month, until they begin to buzz and tick, again, and you'll have to re-adjust them.

They're cheap; that counts in their favour. The build-quality is not atrocious but neither is it worthy of any modicum of commendation.

Mine still stand, behind my stage piano, remaining just tolerable enough to warrant no upgrade. I have learned how to deal with their foibles but I hardly recommend them to prospective purchasers.

What do I need from a stand? Minimal practical footprint - ie big enough to be stable but not take too much space - unobtrusive, strong enough to carry expensive equipment safely, adjust to where I want it... these stands do all that for me. I like there is a choice between soft feet and spikes, I used the latter because they are on a fairly soft carpet. I like having a solid pin to hold the upper section at the height you want and the clamp to set the angle you want, this is nice because it can be set tight to not move or left a little loose to allow gentle changes of angle.

All in all, I am very happy with the stands and don't see any negative aspects. I got them in a bundle with monitors because the new monitors are too big for my desk so now I have them at either side and the ideal height. No rattles or vibration noises either just do what they are supposed to.

1. Triangle base is exceptional if you want to put it inside a stand e.g. Jaspers 4R-150B. It does not interfere with the rollers at all.
2. Easy montage, two screws. Bought with ADAM T8V. 5 minutes both max. You need a carpet because of the weight or a piece of carton while assembly not to hurt it on the floor.
3. The pole is not rigid enough, there is flexibility and oscilates if you touch it. If you DO NOT then OK with the sound and the like. No problem of speaker stability because of speaker weight which has inertia.
4. Plastic stripes for no-slipping speakers were partly damaged because of packing. Since there is a large surface there is no problem on the result nor aesthetic because they are underneath. Still the packing is not effective enough.
Overall they do the job which is much like the stand, without loading the stand with something other than keyboards, screen and controllers. It can be put behind it and pushing the stand back can be fit in place as it would be part of the stand.
Adequate or more.

I just acquired the Millennium BS-500 Set studio monitor stands and could not be more pleased with my selection. These stands have certainly taken my studio setup to the next level of professionalism and usefulness.

The BS-500 stands are well-built, having a robust base that supports my studio monitors. The height-adjustable option is not only handy, but it also enables me to position my monitors for the best sound quality.

One of the most notable things for me is the cable management system. It's a little touch, but it makes a big difference in keeping my workstation clean and organised. There are no more tangled cords or tripping risks; it is simply a clean and effective setup.

Assembly was simple, owing to clear instructions and well-designed components. The stands seem sturdy and dependable, giving me confidence that my pricey studio monitors are well supported.

Overall, the Millennium BS-500 Set studio monitor exceeded my expectations. They blend utility, durability, and a stylish style, making them an ideal complement to any home studio or professional recording setup. If you're looking for dependable monitor supports that improve both design and function, the BS-500 set is an excellent alternative.